PFA 430

Get to know Everflon™ PFA 430.

Applications for Everflon™ PFA 430 include high performance thinwall wire coatings; intricate injection molded parts for production of chemicals and electronic parts; and fluid handling systems for high performance chemical filters. With a typical melt flow rate (MFR) of 40, Everflon™ PFA 430 resin is ideally suited for applications requiring a high processing speed and very low viscosity.

Everflon™ PFA 430 is a special purpose fluoroplastic resin available in pellet form. This resin has a higher melt flow rate (typical MFR of 40) than most other PFA fluoroplastic resins, which permits higher extrusion speed and easier processing, making Everflon™ PFA 430 a costeffective alternative for producing thin-wall and complicated articles.

Unlike other high melt flow rate polymers,Everflon™ PFA 430 is specially formulated to provide a high melt flow rate for processing ease, while still providing good flexural properties and stress-crack resistance. These unique properties, coupled with the resin’s high thermal stability, enable thin coatings of ultra-fine wires and injection molding of complex parts.

Everflon™ PFA 430 combines the processing ease of conventional thermoplastics with many properties similar to those of polytetrafluoroethylene. Compared to other thermoplastics, the high melt strength and thermal stability of Everflon™ PFA 430 can be used to improve processing rates, and allows intricate electronics to be insulated with an extremely thin coating and still withstand soldering. Properly processed products made from neat Everflon™ PFA 430 resin provide the superior properties typical of the fluoroplastic resins: chemical inertness, exceptional dielectric properties, heat resistance, toughness and flexibility, low coefficient of friction, non-stick characteristics, negligible moisture absorption, low flammability, performance at temperature extremes, and excellent weather resistance.

In a flame situation, products of Everflon™ PFA 430 resist ignition and do not promote flame spread. When ignited by flame from other sources, their contribution of heat is very small and added at a slow rate with very little smoke.

Related Products

PFA 420
PFA 410
PFA 403
PFA 430

Data List

Typical Property Data for Everflon™ PFA 430 Fluoroplastic Resin

General Property Data for Everflon™ PFA 430

Properties	Test Method&Unit	Typical Value
Specific Gravity	ASTM D792	2.15
Critical Shear Rate, 372 °C (702 °F)	1/s	250
Flexural Modulus	ASTM D790/ MPa (psi) 23 °C (73 °F) 250 °C (482 °F)	625 (90,000) 69 (10,000)
MIT Folding Endurance (0.20 mm, 8 mil film)	ASTM D2176 Cycles	4,000
Hardness Durometer	ASTM D2240	D55
Dielectric Strength, Short Time, 0.25 mm (0.010 in)	ASTM D149 kV/mm	>80(2,000)
Dielectric Constant, 1 MHz (10⁶Hz)	ASTM D150	2.03
Dissipation Factor, 1 MHz (10⁶Hz)	ASTM D150	<0.0002
Volume Resistivity	ASTM D257 / ohm·cm	10¹⁸
Water Absorption, 24 hr	ASTM D570 %	<0.03
Weather and Chemical Resistance		Outstanding
Limiting Oxygen Index	ASTM D2863 %	> 95%
Continuous Service Temperature	°C (°F)	260 (500)
Flammability Classification	UL 94	V-0

Typical Applications

Applications for Everflon™ PFA 430 include high performance thinwall wire coatings; intricate injection molded parts for production of chemicals and electronic parts; and fluid handling systems for high performance chemical filters. With a typical melt flow rate (MFR) of 40, Everflon™ PFA 430 resin is ideally suited for applications requiring a high processing speed and very low viscosity.

Processing Guide

Everflon™ PFA 430 can be processed by conventional melt extrusion, and by injection, compression, and transfer molding processes. High melt strength and heat stability permit the use of relatively large die openings and high temperature draw-down techniques that increase production rates. Reciprocating screw injection molding machines are preferred.

Corrosion-resistant metals should be used in contact with molten fluoroplastic resin. Extruder barrel should be long, relative to diameter, to provide residence time for heating the resin to approximately 390 °C (730 °F).

Precaution

Equipment used to process at melt temperatures should be provided with local exhaust ventilation (LEV) to completely remove all fumes and vapors from the processing area. In addition, care should be exercised to avoid the contamination of cigarettes and other forms of smoking tobacco when using fluoroplastic resins. Before processing any fluoroplastics, read the Material Safety Data Sheet.

Package

The properties of Everflon™ PFA resin are not affected by storage time. Ambient storage conditions should be designed to avoid airborne contamination and water condensation on the resin when it is removed from containers.
Everflon™ PFA is supplied as pellets and is available in 25-kg multilayer bags with an integral polyethylene liner.


All the must‑haves.
All on Everflon™ PFA 430

			Enabling Improvements and Innovations For more than 20 years, Everflon™ fluoropolymers have provided critical applications with unparalleled performance and durability. Today, the Everflon™ portfolio provides leading-edge solutions that create production and process improvements, ensure superior performance standards, & allow manufacturers to pursue new markets.


Everflon™ PFA 430 for The World Advanced Market.


Keep exploring Everflon™.
Polymer of Dreams


			CREATING A BETTER WORLD THROUGH THE POWER OF OUR FLUOROPOLYMERS Our responsible fluoropolymers helps build a sustainable future for all. Visit Everflon Academic Center -->